As you devor this article, remember that the rest of it contains valuable information related to Rca Female for your reading pleasure. This piece will provide you with not just general Rca Female information but also specific and helpful information.
how do i connect 2x RCA Phono Female to 1x 3.5mm Male Jack Audio Cable to get sound for my ps3?
i brought a ps3 hdmi to dvi cable to go to my tv monitor LG, however as dvi doesnt do sound Rca Female i was recommended to buy 2x RCA Phono Female to 1x 3.5mm Male Jack Audio Cable but how do you connect that to the ps3 to get soundhttp://www.amazon.co.uk/Phono-Female-3-5mm-Audio-Cable/dp/B000Q8KSS0/ref=cm_cr-mr-titlehttp://www.amazon.co.uk/Ps3-Hdmi-Dvi-Cable/dp/B000NWQULS/ref=sr_1_3?ie=UTF8&s=electronics&qid=1228224292&sr=1-3where is the analouge audio out on the ps3
Powered by Yahoo! Answers
 |  |  |
 |  |  |
 |
Be careful here, you try to drive a headphone from an audio output designed to drive an amplifier.”Can I use the output of a preamplifier to drive headphones directly? Maybe. Preamplifier outputs are not designed to drive headphones. They may have very high output impedance and not have enough current capability to drive headphones adequately. Preamps with buffered outputs will probably work. There is a risk that the headphones will draw too much current and damage the preamp’s output stage. For more information, see the Audio Cables section of A Quick Guide To Headphone Accessories. “
NoYou need to open the device and replace the connector. Or if it is a cable, simply replace the cable.
Radio Shack has all the cables you need, in stock and fairly cheap. I haven’t seen a laptop that will allow you to record composite video though. (the kind of video your VCR puts out) Be sure you have that capability before investing in cables. If you don’t, there may be a PCM/CIA card out there that will do the trick. I’ve not seen one of those either though.
Many times you don’t need a transformer. The xlr connecter is usually used for a balanced circuit. You can use one for an unbalanced circuit with no problem. You can also adapt a balanced circuit to an unbalance circuit simply by grounding one of the wires in the balanced circuit. This is probably what your adaptor is doing. In the large majority of cases this works just fine. The only time you need a transformer is if you are changing impedances.
Those adapters will NEVER work.Composite TV signal (single RCA jack) is completely different from monitor VGA. A mere cable CANNOT convert a video signal from one format to another.Those cable adapters are meant for special use only, for video cards that have a specially-built VGA port capable of sending out a composite signal to connect to an old low-definition boob-tube TV.The only way you can convert a composite signal to VGA is with a signal converter box that has the electronics to translate the signal.
Sounds fishy to me. Most speakers connect through wire, bannana plugs, or screw plugs. I wouldn’t buy an amp without a speaker wire hookup The RCA connectors are typically for multiple sub setups.You can always and strip one end of an RCA cable and try that.But I would advise you to look around. Why not get a seperate speaker sub amp setup?
check out partsexpress.com too.
Check out these folks: http://www.mcmelectronics.com/search.aspx?K=TRS%201/4%22%20female%20cable&T=R
A banana plug is a single wire plug, while an RCA plugs is two wires, one for the audio & another to shield the audio.
You shouldn’t. Video is impedance matched, and paralleling loads just throws that out od whack, possbly enough not to work.
A connection is likely loose inside the TV.Unplug the TV and lay it, face down, on something soft that will not scratch the display.Unscrew and remove the case. Finding all of the screws is often the hardest part.Look at the bad RCA connector and follow its connections inside the TV. Look at PC board traces to try to follow the signal. Where it connects to a chip, follow the other pins of that chip.Look, in particular, at connectors within the TV. Connections are often the source of failures.Disconnect and reconnect any connectors.Try it out if possible, being careful not to stick any part of your body into any part of the TV that might have a high voltage. If it does not work, look around more.Put the case back on the TV.If it still does not work, look in the phone book or a search on Google Maps for your nearest TV repair shop.
your best be would be to buy 2 set’s of or jack’s from radio shack and the’ll split 2 female’s 1 male , so you’ll need to get two set’s but thats a quick fix . and should be about 20$
Yes, you can get cables like this in any combination of inputs and outputs. Lots of places on the Web – just Google “stereo female to rca female “.–or–Go to cablestogo.com
Check your local dollar store. The ones around here have those sorts of things.Really you should use an active video splitter though.
It should work and there is no reason why it wouldn’t if all the connectors are connected properly. I’d check the connections to make sure they’re snug and that all of the colors match up.
yes this will work…all u gotta know which is positive (+) and which one is negative (-).
Speakers, yes if they are amplified like computer speakers are.Raw speakers, no, you need an amplifier for that.